Morning: FLAO communication debugging... no real output.

13:00: FLAO comminication star to work... we setup to close TT on PYR, no disturb

TN	AO Gain	Res. WF [nm rms]	AO rec	DIMM ["]	JCL	PCL	Modalplot
20151213_211353	0.95,0.45,0.45	108.069	20151211_202800	-1	T	F
20151213_211513	1.1,0.35,0.35	87.3731	20151211_202800	-1	T	F
20151213_212227	0.5,0.5,0.5	187.55	20151212_220700	-1	F	F

Pupils were misplaced, we set them back to the original position used to acquire IM:

TN	AO Gain	Res. WF [nm rms]	AO rec	DIMM ["]	JCL	PCL	Notes	Modalplot
20151213_212324	0.5,0.45,0.4	165.385	20151212_220700	-1	F	F	-
20151213_212350	0.5,0.4,0.4	167.839	20151212_220700	-1	F	F
20151213_212359	0.5,0.4,0.4	170.709	20151212_220700	-1	F	F
20151213_212715	0.5,0.5,0.5	174.349	20151212_220700	-1	F	F	all pupils down by 5st
20151213_212847	0.5,0.5,0.5	190.112	20151212_220700	-1	F	F	all down 10 st
20151213_212952	0.5,0.5,0.5	185.576	20151212_220700	-1	F	F	original
20151213_213400	0.5,0.5,0.5	172.144	20151212_220700	-1	F	F	pup pos opti by eye

So we set motors in the following position:

Beam	X	Y
Blue	320	430
Yellow	370	458
Red	495	432

Pupil target tag: 20151213_214805

Board

-74.1

-45.7

So to resume we must set an offset of [3.4; 3.4]mm in the AARB.

HEXA

4.28

-0.077

-0.754

250

-158

TN	AO Gain	Res. WF [nm rms]	AO rec	DIMM ["]	JCL	PCL	Notes	Modalplot
20151213_214903	0.5,0.5,0.5	182.932	20151212_220700	-1	F	F	.
20151213_214924	0.5,0.5,0.5	177.832	20151212_220700	-1	F	F	.

Then we load 1" equivalent disturb:

TN	AO Gain	Res. WF [nm rms]	AO rec	DIMM ["]	JCL	PCL	Notes	Modalplot
20151213_215643	1,0.4,0.4	86.5389	20151211_202800	-1	T	F
20151213_220506	0.5,0.4,0.35	95.7312	20151211_202800	-1	T	F
20151213_220557	0.5,0.4,0.35	92.4656	20151211_202800	-1	T	F
20151213_221059	0.5,0.4,0.35	116.611	20151211_202800	-1	T	F	TS coverged at 2nm rms
20151213_221145	0.5,0.4,0.4	117.548	20151211_202800	-1	T	F
20151213_221204	0.5,0.4,0.4	109.866	20151211_202800	-1	T	F
20151213_221353	0.5,0.45,0.45	120.934	20151211_202800	-1	T	F

-- MarcoBonaglia - 13 Dec 2015