Description The 3 acquisition units in each LgswUnit are based on AVT GC1350 cameras. The 12V power supply is installed in the MoCon. The ethernet cable is connec...
The BCU is acting as: frame grabber, slope computer, High Voltage Controller for the tip tilt mirrors, collector of slopes from the FLAO BCU and from the TipTiltU...
Description The beam correctors get rid of the astigmatismus the deformed UoA LMs introduce Documentation attach and describe datasheets and documents Installat...
Description This cables connects the StepperMotorAdaptorBox to the MoCon. They are 1 to 1 cables with military connectors on both side. Each cable is used to cont...
Description Cables used to connect the PI S334 to the BCU. Each piezo head has 5 cables terminated with LEMO connectors: 3 for the HV commands (Axis 1, Axis 2, 10...
The CalUnitSystem (or Calibration Unit) is the ARGOS source used for AO calibration in day time. It creates 3 beams that mimics the 3 LGS beams: 532nm narrow band...
Description The dark wheel consists of the mechanical wheel and the DarkWheelMotor (a motor and a limit switch board with Hall sensor). The magnet is glued on the...
Description The dark wheel motor consists of the motor and the limit switch board with Hall sensor. The magnet is glued on the wheel. The motor and the limit swit...
Documentation attach and describe datasheets and documents Installation and maintenance describe what is needed to put a new device of this kind into operation s...
This is a RTA Xmind K ??? controller to control 1 axis of a dichroic unit. See also DichroicControllerAndWebIOModule Documentation * Programmer manual * In...
Description It is a rack mount 4U module containing 2 DichroicControllers, 1 LedSources, 1 web i/o interfaces. They are used for .... Documentation * Control ...
Description There are 2 C ring electronic racks is installed on the LBT C ring extension. They contains shared devices between the whole ARGOS system. Since they ...
Description There are 2 electronic racks is installed on the Laser Launch Platform. They contains power distribution, cooling and other LAS devices. They contain ...
Description There are 2 electronic racks is installed on the Laser Supply Platform. They contains power distribution, cooling and other LAS devices. They are atta...
Description The LGSW electronic rack is installed on the LUCI platform. It contains all the devices to control the LgswUnit and the LgswDichroic. It needs 110VAC ...
Bundle with three Ethernet Cables (blue, yellow, red) for Patrol Cameras Documentation attach and describe datasheets and documents Installation and maintenance...
Description The InnoLas NANIO 532 18 Y laser head Documentation * Laser Datasheet: nanio_532_18_y.pdf * Laser User and Installation Manual: nanio_user_en_...
Bundle with one EthernetCablesThor and one PowerCableThor (6m). Documentation attach and describe datasheets and documents Installation and maintenance describ...
Description The term "LAN System" refer to all the HW and SW related to the ARGOS launch system on a single LBT eye. A LAN System includes all the components from...
Description The term "LAS System" refer to all the HW and SW related to the ARGOS laser system on a single LBT eye. A LAS System includes a LAS Unit (the box cont...
Bundle with three Optical Fiber (THORLABS, BFL48 600), going from LedSources to LgswUnit. Total of 7 fibers were bought. 6 are grouped, 1 is alone as spare in the...
Description Documentation Design document: Low_inc_dichroic_report_v1.7.pdf For informations about the motor controllers hosted in the electronic rack see Dichro...
Description The term "LGSW System" refer to all the HW and SW related to the ARGOS laser guide star wavefront sensor on a single LBT eye. An LGSW system is compos...
Description The table bolted to the rotator gallery on which the LgswUnit is clamped. It also hosts the cooling line manifold Documentation attach and describe ...
Description The black, t shaped box containing the LGSW WFS. Includes patrol camera, Pockels cell driver and detector Documentation attach and describe datasheet...
Description SMD8 V2 board to drive stepper motors Documentation attach and describe datasheets and documents Installation and maintenance describe what is neede...
Description The Mocon V2 board that is inserted in the MoCon. It manages communication to the MoCon modules Documentation See MoCon for manuals. Installation an...
Description It is a rack mount 4U module containing motor controllers for the LMs shutters, 1 LedSources, 1 web i/o interfaces. Documentation Cabling schematics:...
Description These motors are used to adjust the pupil position in the LgswUnit. They are customized: the connector has been replaced with a DB9 to plug into the S...
Description These are diaphragm pumps used to extract air from the EM shield in the LgswUnit where the PockelsCells are installed. These devices were added to the...
Description The servo switches are intended to choose, if the piezos are operated in open (off) or closed loop (on). Upper switch: X axis Lower switch:Y axis Doc...
Description Jitter compensation in the LGSW is done by piezo platform PI S334.1SL Documentation attach and describe datasheets and documents Installation and ma...
Description A device in the rack with an on off button and a potentiometer to adjust HV tension. This is an obsolete model, it has been upgraded in Jun 2015. See ...
Description A device in the ElectronicRackLgsw to supply high voltage to the PockelsCellDriverV2. This is a replacement of PockelsCellAmplifier, in operation sinc...
Description This device is installed on a side of the LgswUnit. This is an obsolete device, replaced by PockelsCellDriverV2 Documentation attach and describe dat...
Description This device is installed on a side of the LgswUnit. This is the current version of the device, replacing PockelsCellDriver Documentation attach and d...
Description Versions The are several version of this device: * The 2012 model (aka v1.0) that have shown degradation of plastic holders due to ozone pollution...
Description There are 2 versions of these cable boundles: * The 2012 version, serving the PockelsCellAmplifier: it is a boundle of 5 cables, 4 coaxials with BN...
Power line cable for WavecommThor. Male: http://it.rs online.com/web/p/connettori din/5336720/ Female: http://it.rs online.com/web/p/connettori din/5334881/ Inter...
Bundle with three power line cables for Patrol Camera. Documentation attach and describe datasheets and documents Installation and maintenance describe what is ...
Quantum Composer 9530 series pulse generator Documentation attach and describe datasheets and documents 9530_Manual.pdf Installation and maintenance describe wh...
Description These motors are used to move Dichroic and Fold Mirror in the LgswDichroicSystem. Official name: Sanyo Denki, SM2862 5055 Documentation SM_2862 5055....
Description Adaptor box is installed inside the LgswUnit. It gets up to 8 motor connected via DB9 connection on the internal side. On the external side it has 2 m...
Documentation attach and describe datasheets and documents Installation and maintenance describe what is needed to put a new device of this kind into operation s...
Description This device monitors the temperature and humidity values of the LaserSystem. Documentation * User manual: http://abell.as.arizona.edu/~hill/xlbt...
Description Sensors with Sensirion SHT21 and RJ connector assembled by Wavecomm. There are several kinds of probes: 1 The ones named THxx with xx greater than ...
Description The Tip Tilt System is composed by: * An ApertureWheel used to set the Tip Tilt system FoV * A QuadCellUnit installed on the technical viewer ar...
Description This is the Tip Tilt Unit that is made of: i. the TipTiltComputer a.k.a. Bonn unit i. the TipTiltIOSwitch a.k.a. Moxa N port i. the APDModule...
Description The ARGOS vibration control system is designed to detect vibrations on the instrument optical path at a level sufficient to calculate and mitigate the...
Description A WfsCamera device is the fast speed camera of the SH WFS unit. It is installed at the end of the LgswUnit. This topic refers only to the camera head....
Description A device in the ElectronicRackLgsw, composed by PcKontron, Sequencer, TemperatureController and PowerSupply Documentation attach and describe datashe...
This is the pump that is needed to vacuum the WfsCamera Checking camera housing pressure and pumping it out Reading the pressure * (the software pressure meas...
Description This is a big boundle of cables connecting the WfsCamera to its electronic inside the ElectronicRackLgsw Documentation attach and describe datasheets...
Description The ARGOS workstations. They are DELL PowerEdge R510 and R520 See the twiki of MPIA: https://svn.mpia.de/trac/gulli/argos/wiki/Workstations Refer to M...