18:30: begin of operations we point to: HESS_J1943p213 * HESS_J1943p213_20161020.pdf Beam shaping: corrector at 255 and focus stage at 75k steps. TN AO G...
22:00: we get the telescope from LUCI/AO. We disconnect fibers, we try to collimate. 22:30: beam shaping. CCD39 fails to configure G1 * G1_20161019.pdf TN ...
We have to exchange the PockelsCellDriver6 on the SX side, it fails to power up... ETG0895 * ETG895_20161022.pdf 18:30: pointing telescope. TN AO Gain A...
LgswSystem test w/ PYR 9:00: we startup both systems but we first try to close a loop w/ PYR on the DX system. TN AO Gain AO CL TT Res. WF nm rms HO R...
LgswUnitDx work LgswUnitDx installation 9:00: we go up to crane back the LGSW: ML leads the operation. 12:00: installation completed, we go back to control r...
On telescope work (MB, SR, ML) 9:00: up on telescope to put back LgswUnitSx red EW that was moved when cleaned... Then we check the LgswUnitDx that had a spot on ...
LgswUnitSx AO calibration 6:45: start of operations, we try to power up from arbitrator. SX BCU fails to boot twice, then we power cicle from Rack I/O and it work...
* install and test new limit switches on ARGOS calibration source swing arms (SX DX) * removal of temporary diagnostic lines on SX ARGOS laser boxes, racks a...
LgswUnitSx test w/ ASM We cheked again the PC behavour after 1 night at 40% RH. The BLue and Yellow still look bad: We could close the loop w/ LGSW only and the m...
Summary of AO loop calibrations for the ArgosSystemDx Table below resumes the latest combined reconstructors built and tested in daytime: Combination Tag Suba...
This is a RTA Xmind K ??? controller to control 1 axis of a dichroic unit. See also DichroicControllerAndWebIOModule Documentation * Programmer manual * In...
Power up issues When we power up the SX LGSW the Pupil motor RED Y axis was not homing. We unmount the LGSW panel and we push by hand the stage and at this point ...
14:00: We switch on DX side. DX LGSW pulse generator is working, WFS camera and BCU are working at 970 Hz. 15:00: We pump the SX WFS camera, pressure was 90mbar o...
!!!! Keep track of your work !!!! !!!! Remember to keep track of the recorded IMs and all RECs built into the following pages: * DXAoLoopCalibrations * SXAo...
Howto Acquire Frames With Patrol Camera At Full Speed Data acquired using tools in: argos@sx lgsw x64 $ pwd /home/argos/Downloads/AVTCam/AVT GigE SDK/bin pc/x64 ...
GC1350 configuration Setting IP address 1 Download and install the AVT/Prosilica GigE SDK from http://www.alliedvisiontec.com/us/products/software. This guide...
This topic contains the instructions to optimize the spot on the Patrol Cameras moving the Launch Beam Corrector and the Focus Stage in the Lan System. DX With t...
Log * List of action items for the run: Argos_tasks_20160913.xlsx, argos_sw_ai_may2016_wg20160815.xlsx * List of SW action items for the run: argos_sw_action...
Test of pupil recentering w/ slope rms We switch on the system and setup for Pyramid TT. We find again that pupils are not in the proper position (from illuminati...
LgswUnitDx test w/ PyramidWfs We put back the systems as it was yesterday, but we find that the pupils are quite shifted (approx 20 30 motor steps). We close the ...
10:00 LAT/05:00 UT Handover from LUCI/AO * Lorenzo Gustavo where switching fibers. * SX dichroic got stuck while authorization. * Authorization failed ...
17:00: we start to power up the DX system from the new Centos7 machines. We see many problems: i. the GUIs are very lagged, expecially the ones displaying came...
LgswDichroicSystemSX interlock check 9:00: handover from LUCI guys. We go up to check for the SX dichroic interlock failures. We set back the ARGOS interlock cabl...
The CalUnitSystem (or Calibration Unit) is the ARGOS source used for AO calibration in day time. It creates 3 beams that mimics the 3 LGS beams: 532nm narrow band...
LUCI work until 5:00 UT Telescope to horizonFixing SX LM1 A1 absolute encoder. Reset to 0.Unintentionally done first at DX, therefor DX and SX LM A1 encoder were ...
Log * List of action items for the run: Argos_tasks_20160913.xlsx * List of SW action items for the run: argos_sw_action_items_may2016_lb20160713.xlsx * Sc...
Work on LM1 to make it moth tight. (Hans, Matthias) Checking out new fiber switch. Didn't work out.Light suppression was to high. Main.WolfgangGaessler 24 Oct...
we give 2h for LUCI1 calibrations... Test of VibComp effects on Patrol cameras 20:30: launching lasers at Zenith to check LAT pointing model. 20:45: we check the...
21:00: spotters are out BDS2003 65 the available guide star is too faint. We change target Hip1813 22:20: AArb configured for magnitude 16. 23:30: FLAO slopes f...
18:00: back to SX, we setup for the night We start testing the new telescope offset procedure. We have a first try and the AOS hangs: Mar May 16 03:05:56 DX syste...