Detailed topic list for ARGOSPublic Web

Results from ARGOSPublic web retrieved at 23:51 (GMT)

DayTime20151210

PBL: we have found a problem with slopes reordering... We close a loop with LGSW only REC: 20151209_213200 w/o disturb. TN AO Gain Res. WF nm rms AO rec...

r3 - 08 Jan 2016 - 13:41 by MarcoBonaglia

DayTime20151211

Test of DX LGSW with CalUnit and rigid secondary (afternoon) Problems with Arbitrator * Restart not possible in situation of shutdown of LAS and powering_up of...

r3 - 08 Jan 2016 - 14:49 by MarcoBonaglia

DayTime20151212

Test of DX LGSW with CalUnit and rigid secondary Hexapod settings with rigid secondary: Right PSF 2ndary X Y Z Rx Ry Rz 4.75 8.30 5.15 4.9...

r5 - 08 Jan 2016 - 17:01 by MarcoBonaglia

DayTime20151213

Morning: FLAO communication debugging... no real output. 13:00: FLAO comminication star to work... we setup to close TT on PYR, no disturb TN AO Gain Res. W...

r2 - 08 Jan 2016 - 17:22 by MarcoBonaglia

DayTime20160307

13:00 arrival at telescope SX PnCCD pumped (WfsCamera1). Before pumping the SW red 49.5mbar, after pumping 0.02mbar. DX PnCCD (WfsCamera2) was fine, no pumping ne...

r2 - 10 Mar 2016 - 02:08 by GillesOrban

DayTime20160308

8:20: SX CalUnit is in Hexapod set ack to December position: 4.98; 0.39; 0.61; 211; 100 , and FLAO board to: 73.8; 45.9; 45.0 . PBL with crane give us no te...

NEW - 10 Mar 2016 - 02:19 by MarcoBonaglia

DayTime20160309

In the morning telescope is dedicate to LUCI1 MOS exchange. 12:15: telescope released, SX and DX CalUnit deployed. LgswUnitSx FoV measurement We do a sweep of /...

r2 - 02 Mar 2021 - 08:48 by AlfioPuglisi

DayTime20160310

7:30: power up of DX and SX systems. RR cubes are mounted back on both sides. Side PCT SX DX TipTiltSystemSx calibrations We setup the SX AGW...

NEW - 11 Mar 2016 - 02:10 by MarcoBonaglia

DayTime20160311

SX QC and Pyramid co pointing We switch on the AGW and we configure it to be used with IS. FW1: 600 1000, we center on QC. Board 72.3 50.1 35.0 Then w...

r4 - 07 Apr 2016 - 12:44 by TommasoMazzoni

DayTime20160312

LgswUnitDx FoV adjustment to CalUnit We adjusted the position of the LGSW EW to match the cal unit sources, below a summary of the measurements: * 20160312_DX ...

r2 - 11 May 2016 - 22:23 by TommasoMazzoni

DayTime20160510

13:30: Arrival at telescope 16:00: we try to start up both systems. Due to power outage the SX LGSW computer was off, we turned it on again. The DX LGSW computer ...

r4 - 11 May 2016 - 21:50 by MarcoBonaglia

DayTime20160511

LgswUnitSx and LgswUnitDx HW servicing 8:00: we unpack the PCD and the amplifier from 3L boxes, we bring it to 5. We also spend 1:30h in searching for the WfsCame...

r7 - 23 May 2016 - 02:30 by LorenzoBusoni

DayTime20160512

5:30: Gustavo deploys the arm, we have pbl starting AdSecSx: it periodically faild while loading the DSP program. We try many times to power cicle. LB finally can...

r6 - 13 May 2016 - 15:16 by TommasoMazzoni

DayTime20160513

TT w/ Pyr Bin4 test 8:00: we start with PyrWfs, setup as Bin4, mag 15. * CCD47 is not set to Bin16 during the preset * TS at Bin4 is missing the KL basis at...

r4 - 24 May 2016 - 12:03 by MarcoBonaglia

DayTime20160514

Laser Power Test Measured sum power: * SX 43.256 * DX 48.631 SIDE L1 L2 L3 DX Field cam 15.50 18.06 18.17 DX Calorimeter 15.59 17.06 15.63 SX ...

r9 - 15 May 2016 - 07:33 by TommasoMazzoni

DayTime20160515

Fast guiding check w/ oscilloscope 11:30: Tommaso and Sebastian go on the telescope to check the Fast Guiding delay. We connect an oscilloscope after the 10x divi...

r8 - 24 May 2016 - 12:24 by MarcoBonaglia

DayTime20161011

Visual check 15:00: we climbed on telescope and had a visual check of the LGSWs and LAS boxes status. * The 2 LGSWs appear very muddy, a lot of mud water accum...

NEW - 12 Oct 2016 - 01:40 by MarcoBonaglia

DayTime20161012

Visual Inspection 11:00: telescope back to Zenith, we climb and check the racks: fine. The pressure gauge on SX PNCCD had low battery. We pumped it anyway up to 0...

r5 - 13 Oct 2016 - 00:42 by MarcoBonaglia

DayTime20161013

LgswUnitSx AO calibration 6:45: start of operations, we try to power up from arbitrator. SX BCU fails to boot twice, then we power cicle from Rack I/O and it work...

r5 - 28 Apr 2017 - 02:38 by MarcoBonaglia

DayTime20161014

On telescope work (MB, SR, ML) 9:00: up on telescope to put back LgswUnitSx red EW that was moved when cleaned... Then we check the LgswUnitDx that had a spot on ...

r4 - 28 Apr 2017 - 02:45 by MarcoBonaglia

DayTime20161015

LgswUnitDx work LgswUnitDx installation 9:00: we go up to crane back the LGSW: ML leads the operation. 12:00: installation completed, we go back to control r...

r4 - 28 Apr 2017 - 02:51 by MarcoBonaglia

DayTime20161016

LgswUnitDx work 8:30: WG and MR go to check the cal unit illumination patter. It seems ok, maybe an alignment problem? 10:20: BcuNumber3 fails to connect. We must...

r2 - 20 Oct 2016 - 10:56 by MarcoBonaglia

DayTime20161017

Sx side New Hexapod position after Coma Correction: SX HEXA 4.28 2.72 0.3 39 17 0 Comparison between QC and Pyramid To test the best gain and ...

r6 - 28 Apr 2017 - 02:58 by MarcoBonaglia

DayTime20161018

DX side LgswUnitDx FoV measurement New Hexapod positions after coma removal: DX HEXA 1.60 4.18 1.18 181.5 79 We try to measure the FoV of the LGS...

r4 - 20 Oct 2016 - 23:58 by TommasoMazzoni

DayTime20161021

LgswDichroicSystem check In the last days we found many issues with the movement of both the dichroic and fold mirror on the LgswDichroicSystemSX while on the Lgs...

r2 - 22 Oct 2016 - 21:30 by MarcoBonaglia

DayTime20161022

Work on LM1 shutter. Making it moths proof. (Hans and Matthias) Main.WolfgangGaessler 23 Oct 2016

r2 - 28 Oct 2016 - 13:48 by MarcoBonaglia

DayTime20161023

Work on LM1 to make it moth tight. (Hans, Matthias) Checking out new fiber switch. Didn't work out.Light suppression was to high. Main.WolfgangGaessler 24 Oct...

r2 - 28 Oct 2016 - 13:48 by MarcoBonaglia

DayTime20161024NightTime20161024

Cooling upgrade and LM greasing moths tight (Hans Matthias). Main.WolfgangGaessler 25 Oct 2016

NEW - 25 Oct 2016 - 07:04 by WolfgangGaessler

DayTime20161202

17:00: we start to power up the DX system from the new Centos7 machines. We see many problems: i. the GUIs are very lagged, expecially the ones displaying came...

r2 - 04 Dec 2016 - 01:35 by MarcoBonaglia

DayTime20161203

LgswDichroicSystemSX interlock check 9:00: handover from LUCI guys. We go up to check for the SX dichroic interlock failures. We set back the ARGOS interlock cabl...

r3 - 04 Dec 2016 - 01:03 by MarcoBonaglia

DayTime20161204

LgswUnitSx test w/ ASM We cheked again the PC behavour after 1 night at 40% RH. The BLue and Yellow still look bad: We could close the loop w/ LGSW only and the m...

r3 - 28 Apr 2017 - 00:17 by MarcoBonaglia

DayTime20161205

LgswUnitDx calibrations FoV measurement DX HEXA 3.94 2.36 0.73 174 384 We try to measure the LGSW FoV, we close the loop w/ 2015/07 rec but tod...

r2 - 08 Dec 2016 - 02:42 by MarcoBonaglia

DayTime20161206

LgswUnitDx test w/ PyramidWfs We put back the systems as it was yesterday, but we find that the pupils are quite shifted (approx 20 30 motor steps). We close the ...

r2 - 08 Dec 2016 - 06:03 by MarcoBonaglia

DayTime20161207

Test of pupil recentering w/ slope rms We switch on the system and setup for Pyramid TT. We find again that pupils are not in the proper position (from illuminati...

NEW - 08 Dec 2016 - 06:41 by MarcoBonaglia

DayTime20170301

14:00: We switch on DX side. DX LGSW pulse generator is working, WFS camera and BCU are working at 970 Hz. 15:00: We pump the SX WFS camera, pressure was 90mbar o...

NEW - 02 Mar 2017 - 00:33 by TommasoMazzoni

DayTime20170302

Power up issues When we power up the SX LGSW the Pupil motor RED Y axis was not homing. We unmount the LGSW panel and we push by hand the stage and at this point ...

NEW - 03 Mar 2017 - 01:58 by TommasoMazzoni

DayTime20170303

SX AO Calibration New Pupil motors position BLUE 330 420 YELLOW 371 443 RED 495 402 New calibration 150 modes in OL MH LGSW IM LGSW ...

r4 - 28 Apr 2017 - 00:45 by MarcoBonaglia

DayTime20170304

DX AO test New flat on DX adsec with 400 modes made in CL with FLAO. Test old recontrstuctor with 0.8" disturbance. TN AO Gain AO CL TT Res. WF nm rms ...

r4 - 26 Jun 2017 - 09:48 by TommasoMazzoni

DayTime20170427

* install and test new limit switches on ARGOS calibration source swing arms (SX DX) * removal of temporary diagnostic lines on SX ARGOS laser boxes, racks a...

NEW - 28 Apr 2017 - 02:29 by MarcoBonaglia

DayTime20170428

LgswSystemSx and LgswSystemDx resume 8:00: startup DX we have several problems: i. error camera: PSU is not communicating, we reboot the Kontron and it is solv...

r2 - 29 May 2017 - 08:55 by TommasoMazzoni

DayTime20170429

LgswSystem test w/ PYR 9:00: we startup both systems but we first try to close a loop w/ PYR on the DX system. TN AO Gain AO CL TT Res. WF nm rms HO R...

NEW - 30 Apr 2017 - 05:45 by MarcoBonaglia

DayTime20170430

Morning: * JZ fixes a fuse that was burnt because of the new piezo electronics required too much power. * Checking for the poweron poweroff procedures from ...

r3 - 01 May 2017 - 05:57 by MarcoBonaglia

DayTime20170501

NEW - 01 May 2017 - 20:51 by MarcoBonaglia

DayTime20170503

LgswSystemSx test with sinusoidal REC * Old REC TN AO Gain AO CL TT Res. WF nm rms HO Res. WF nm rms AO rec DIMM " JCL PCL Notes ...

r3 - 05 May 2017 - 09:56 by MarcoBonaglia

DayTime20180220

DX AO calibration New pupil motors positions: Pupil PMX PMY Blue 405 510 Yellow 310 345 Red 410 320 The new KL_v22 is different re...

NEW - 21 Feb 2018 - 04:18 by TommasoMazzoni

DayTime20180221

DX AO calibration New Flao Rec Bin2, KL_v22: 20180217_202826 New Flao Rec Bin4, KL_v22: 20180219_193910 Procedure to set the new Flao rec in ARGOS: HowToBuildFlao...

NEW - 22 Feb 2018 - 02:36 by TommasoMazzoni

DayTime20180222

SX calibration Interaction matrix for SX: 20180222_153225 The Tip and Tilt in the Interaction Matrix with KL_v18 on SX side look different respect than we expect....

r4 - 15 Mar 2018 - 12:52 by TommasoMazzoni

DayTime20180223

Tests on SX side, one complete rotation of LUCI to test the TS and measure the slopes offset at different ration angle. Worse points (at 280 and 190 deg) are due ...

r2 - 05 Mar 2018 - 14:46 by TommasoMazzoni

DeviceInfoForm

Name Type Size Values Tooltip message Attributes Name text 80 SerialNumber text 40 Location select 1 , MACA...

r7 - 01 Sep 2015 - 12:46 by WolfgangGaessler

DeviceTemplate

Known history When Where Who What 20130215 Know issues When What 20130305 description of issue Current known config IP, firmwar...

r5 - 03 Feb 2016 - 14:29 by MarcoBonaglia

Number of topics: 50

< Previous Page 4 of 15 Next >